stm32f7xx_hal_qspi.h

Go to the documentation of this file.

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F7xx_HAL_QSPI_H
#define __STM32F7xx_HAL_QSPI_H

#ifdef __cplusplus
 extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "stm32f7xx_hal_def.h"

/* Exported types ------------------------------------------------------------*/ 
typedef struct
{
  uint32_t ClockPrescaler;     /* Specifies the prescaler factor for generating clock based on the AHB clock.
                                  This parameter can be a number between 0 and 255 */ 
                                  
  uint32_t FifoThreshold;      /* Specifies the threshold number of bytes in the FIFO (used only in indirect mode)
                                  This parameter can be a value between 1 and 32 */
                                  
  uint32_t SampleShifting;     /* Specifies the Sample Shift. The data is sampled 1/2 clock cycle delay later to 
                                  take in account external signal delays. (It should be QSPI_SAMPLE_SHIFTING_NONE in DDR mode)
                                  This parameter can be a value of @ref QSPI_SampleShifting */
                                  
  uint32_t FlashSize;          /* Specifies the Flash Size. FlashSize+1 is effectively the number of address bits 
                                  required to address the flash memory. The flash capacity can be up to 4GB 
                                  (addressed using 32 bits) in indirect mode, but the addressable space in 
                                  memory-mapped mode is limited to 256MB
                                  This parameter can be a number between 0 and 31 */
                                  
  uint32_t ChipSelectHighTime; /* Specifies the Chip Select High Time. ChipSelectHighTime+1 defines the minimum number 
                                  of clock cycles which the chip select must remain high between commands.
                                  This parameter can be a value of @ref QSPI_ChipSelectHighTime */ 
                                    
  uint32_t ClockMode;          /* Specifies the Clock Mode. It indicates the level that clock takes between commands.
                                  This parameter can be a value of @ref QSPI_ClockMode */
                                 
  uint32_t FlashID;            /* Specifies the Flash which will be used,
                                  This parameter can be a value of @ref QSPI_Flash_Select */
                                 
  uint32_t DualFlash;          /* Specifies the Dual Flash Mode State
                                  This parameter can be a value of @ref QSPI_DualFlash_Mode */                                               
}QSPI_InitTypeDef;

typedef enum
{
  HAL_QSPI_STATE_RESET             = 0x00U,    
  HAL_QSPI_STATE_READY             = 0x01U,    
  HAL_QSPI_STATE_BUSY              = 0x02U,    
  HAL_QSPI_STATE_BUSY_INDIRECT_TX  = 0x12U,    
  HAL_QSPI_STATE_BUSY_INDIRECT_RX  = 0x22U,    
  HAL_QSPI_STATE_BUSY_AUTO_POLLING = 0x42U,    
  HAL_QSPI_STATE_BUSY_MEM_MAPPED   = 0x82U,    
  HAL_QSPI_STATE_ABORT             = 0x08U,    
  HAL_QSPI_STATE_ERROR             = 0x04U     
}HAL_QSPI_StateTypeDef;

typedef struct
{
  QUADSPI_TypeDef            *Instance;        /* QSPI registers base address        */
  QSPI_InitTypeDef           Init;             /* QSPI communication parameters      */
  uint8_t                    *pTxBuffPtr;      /* Pointer to QSPI Tx transfer Buffer */
  __IO uint16_t              TxXferSize;       /* QSPI Tx Transfer size              */
  __IO uint16_t              TxXferCount;      /* QSPI Tx Transfer Counter           */
  uint8_t                    *pRxBuffPtr;      /* Pointer to QSPI Rx transfer Buffer */
  __IO uint16_t              RxXferSize;       /* QSPI Rx Transfer size              */
  __IO uint16_t              RxXferCount;      /* QSPI Rx Transfer Counter           */
  DMA_HandleTypeDef          *hdma;            /* QSPI Rx/Tx DMA Handle parameters   */
  __IO HAL_LockTypeDef       Lock;             /* Locking object                     */
  __IO HAL_QSPI_StateTypeDef State;            /* QSPI communication state           */
  __IO uint32_t              ErrorCode;        /* QSPI Error code                    */
  uint32_t                   Timeout;          /* Timeout for the QSPI memory access */ 
}QSPI_HandleTypeDef;

typedef struct
{
  uint32_t Instruction;        /* Specifies the Instruction to be sent
                                  This parameter can be a value (8-bit) between 0x00 and 0xFF */
  uint32_t Address;            /* Specifies the Address to be sent (Size from 1 to 4 bytes according AddressSize)
                                  This parameter can be a value (32-bits) between 0x0 and 0xFFFFFFFF */
  uint32_t AlternateBytes;     /* Specifies the Alternate Bytes to be sent (Size from 1 to 4 bytes according AlternateBytesSize)
                                  This parameter can be a value (32-bits) between 0x0 and 0xFFFFFFFF */
  uint32_t AddressSize;        /* Specifies the Address Size
                                  This parameter can be a value of @ref QSPI_AddressSize */
  uint32_t AlternateBytesSize; /* Specifies the Alternate Bytes Size
                                  This parameter can be a value of @ref QSPI_AlternateBytesSize */
  uint32_t DummyCycles;        /* Specifies the Number of Dummy Cycles.
                                  This parameter can be a number between 0 and 31 */
  uint32_t InstructionMode;    /* Specifies the Instruction Mode
                                  This parameter can be a value of @ref QSPI_InstructionMode */
  uint32_t AddressMode;        /* Specifies the Address Mode
                                  This parameter can be a value of @ref QSPI_AddressMode */
  uint32_t AlternateByteMode;  /* Specifies the Alternate Bytes Mode
                                  This parameter can be a value of @ref QSPI_AlternateBytesMode */
  uint32_t DataMode;           /* Specifies the Data Mode (used for dummy cycles and data phases)
                                  This parameter can be a value of @ref QSPI_DataMode */
  uint32_t NbData;             /* Specifies the number of data to transfer. 
                                  This parameter can be any value between 0 and 0xFFFFFFFF (0 means undefined length 
                                  until end of memory)*/
  uint32_t DdrMode;            /* Specifies the double data rate mode for address, alternate byte and data phase
                                  This parameter can be a value of @ref QSPI_DdrMode */
  uint32_t DdrHoldHalfCycle;   /* Specifies the DDR hold half cycle. It delays the data output by one half of 
                                  system clock in DDR mode.
                                  This parameter can be a value of @ref QSPI_DdrHoldHalfCycle */
  uint32_t SIOOMode;          /* Specifies the send instruction only once mode
                                  This parameter can be a value of @ref QSPI_SIOOMode */
}QSPI_CommandTypeDef;

typedef struct
{
  uint32_t Match;              /* Specifies the value to be compared with the masked status register to get a match.
                                  This parameter can be any value between 0 and 0xFFFFFFFF */
  uint32_t Mask;               /* Specifies the mask to be applied to the status bytes received. 
                                  This parameter can be any value between 0 and 0xFFFFFFFF */
  uint32_t Interval;           /* Specifies the number of clock cycles between two read during automatic polling phases.
                                  This parameter can be any value between 0 and 0xFFFF */
  uint32_t StatusBytesSize;    /* Specifies the size of the status bytes received.
                                  This parameter can be any value between 1 and 4 */
  uint32_t MatchMode;          /* Specifies the method used for determining a match.
                                  This parameter can be a value of @ref QSPI_MatchMode */
  uint32_t AutomaticStop;      /* Specifies if automatic polling is stopped after a match.
                                  This parameter can be a value of @ref QSPI_AutomaticStop */
}QSPI_AutoPollingTypeDef;
                           
typedef struct
{
  uint32_t TimeOutPeriod;      /* Specifies the number of clock to wait when the FIFO is full before to release the chip select.
                                  This parameter can be any value between 0 and 0xFFFF */
  uint32_t TimeOutActivation;  /* Specifies if the time out counter is enabled to release the chip select. 
                                  This parameter can be a value of @ref QSPI_TimeOutActivation */
}QSPI_MemoryMappedTypeDef;                                     
/* Exported constants --------------------------------------------------------*/
#define HAL_QSPI_ERROR_NONE            ((uint32_t)0x00000000U) 
#define HAL_QSPI_ERROR_TIMEOUT         ((uint32_t)0x00000001U) 
#define HAL_QSPI_ERROR_TRANSFER        ((uint32_t)0x00000002U) 
#define HAL_QSPI_ERROR_DMA             ((uint32_t)0x00000004U) 
#define HAL_QSPI_ERROR_INVALID_PARAM   ((uint32_t)0x00000008U) 
#define QSPI_SAMPLE_SHIFTING_NONE           ((uint32_t)0x00000000U)        
#define QSPI_SAMPLE_SHIFTING_HALFCYCLE      ((uint32_t)QUADSPI_CR_SSHIFT) 
#define QSPI_CS_HIGH_TIME_1_CYCLE           ((uint32_t)0x00000000U)                              
#define QSPI_CS_HIGH_TIME_2_CYCLE           ((uint32_t)QUADSPI_DCR_CSHT_0)                      
#define QSPI_CS_HIGH_TIME_3_CYCLE           ((uint32_t)QUADSPI_DCR_CSHT_1)                      
#define QSPI_CS_HIGH_TIME_4_CYCLE           ((uint32_t)QUADSPI_DCR_CSHT_0 | QUADSPI_DCR_CSHT_1) 
#define QSPI_CS_HIGH_TIME_5_CYCLE           ((uint32_t)QUADSPI_DCR_CSHT_2)                      
#define QSPI_CS_HIGH_TIME_6_CYCLE           ((uint32_t)QUADSPI_DCR_CSHT_2 | QUADSPI_DCR_CSHT_0) 
#define QSPI_CS_HIGH_TIME_7_CYCLE           ((uint32_t)QUADSPI_DCR_CSHT_2 | QUADSPI_DCR_CSHT_1) 
#define QSPI_CS_HIGH_TIME_8_CYCLE           ((uint32_t)QUADSPI_DCR_CSHT)                        
#define QSPI_CLOCK_MODE_0                   ((uint32_t)0x00000000U)         
#define QSPI_CLOCK_MODE_3                   ((uint32_t)QUADSPI_DCR_CKMODE) 
#define QSPI_FLASH_ID_1           ((uint32_t)0x00000000U)
#define QSPI_FLASH_ID_2           ((uint32_t)QUADSPI_CR_FSEL)

#define QSPI_DUALFLASH_ENABLE            ((uint32_t)QUADSPI_CR_DFM)
#define QSPI_DUALFLASH_DISABLE           ((uint32_t)0x00000000U) 

#define QSPI_ADDRESS_8_BITS            ((uint32_t)0x00000000U)           
#define QSPI_ADDRESS_16_BITS           ((uint32_t)QUADSPI_CCR_ADSIZE_0) 
#define QSPI_ADDRESS_24_BITS           ((uint32_t)QUADSPI_CCR_ADSIZE_1) 
#define QSPI_ADDRESS_32_BITS           ((uint32_t)QUADSPI_CCR_ADSIZE)   
#define QSPI_ALTERNATE_BYTES_8_BITS    ((uint32_t)0x00000000U)           
#define QSPI_ALTERNATE_BYTES_16_BITS   ((uint32_t)QUADSPI_CCR_ABSIZE_0) 
#define QSPI_ALTERNATE_BYTES_24_BITS   ((uint32_t)QUADSPI_CCR_ABSIZE_1) 
#define QSPI_ALTERNATE_BYTES_32_BITS   ((uint32_t)QUADSPI_CCR_ABSIZE)   
#define QSPI_INSTRUCTION_NONE          ((uint32_t)0x00000000U)          
#define QSPI_INSTRUCTION_1_LINE        ((uint32_t)QUADSPI_CCR_IMODE_0) 
#define QSPI_INSTRUCTION_2_LINES       ((uint32_t)QUADSPI_CCR_IMODE_1) 
#define QSPI_INSTRUCTION_4_LINES       ((uint32_t)QUADSPI_CCR_IMODE)   
#define QSPI_ADDRESS_NONE              ((uint32_t)0x00000000U)           
#define QSPI_ADDRESS_1_LINE            ((uint32_t)QUADSPI_CCR_ADMODE_0) 
#define QSPI_ADDRESS_2_LINES           ((uint32_t)QUADSPI_CCR_ADMODE_1) 
#define QSPI_ADDRESS_4_LINES           ((uint32_t)QUADSPI_CCR_ADMODE)   
#define QSPI_ALTERNATE_BYTES_NONE      ((uint32_t)0x00000000U)           
#define QSPI_ALTERNATE_BYTES_1_LINE    ((uint32_t)QUADSPI_CCR_ABMODE_0) 
#define QSPI_ALTERNATE_BYTES_2_LINES   ((uint32_t)QUADSPI_CCR_ABMODE_1) 
#define QSPI_ALTERNATE_BYTES_4_LINES   ((uint32_t)QUADSPI_CCR_ABMODE)   
#define QSPI_DATA_NONE                 ((uint32_t)0X00000000)           
#define QSPI_DATA_1_LINE               ((uint32_t)QUADSPI_CCR_DMODE_0) 
#define QSPI_DATA_2_LINES              ((uint32_t)QUADSPI_CCR_DMODE_1) 
#define QSPI_DATA_4_LINES              ((uint32_t)QUADSPI_CCR_DMODE)   
#define QSPI_DDR_MODE_DISABLE              ((uint32_t)0x00000000U)       
#define QSPI_DDR_MODE_ENABLE               ((uint32_t)QUADSPI_CCR_DDRM) 
#define QSPI_DDR_HHC_ANALOG_DELAY           ((uint32_t)0x00000000U)       
#define QSPI_DDR_HHC_HALF_CLK_DELAY         ((uint32_t)QUADSPI_CCR_DHHC) 
#define QSPI_SIOO_INST_EVERY_CMD       ((uint32_t)0x00000000U)       
#define QSPI_SIOO_INST_ONLY_FIRST_CMD  ((uint32_t)QUADSPI_CCR_SIOO) 
#define QSPI_MATCH_MODE_AND                 ((uint32_t)0x00000000U)     
#define QSPI_MATCH_MODE_OR                  ((uint32_t)QUADSPI_CR_PMM) 
#define QSPI_AUTOMATIC_STOP_DISABLE        ((uint32_t)0x00000000U)      
#define QSPI_AUTOMATIC_STOP_ENABLE         ((uint32_t)QUADSPI_CR_APMS) 
#define QSPI_TIMEOUT_COUNTER_DISABLE       ((uint32_t)0x00000000U)      
#define QSPI_TIMEOUT_COUNTER_ENABLE        ((uint32_t)QUADSPI_CR_TCEN) 
#define QSPI_FLAG_BUSY                 QUADSPI_SR_BUSY 
#define QSPI_FLAG_TO                   QUADSPI_SR_TOF  
#define QSPI_FLAG_SM                   QUADSPI_SR_SMF  
#define QSPI_FLAG_FT                   QUADSPI_SR_FTF  
#define QSPI_FLAG_TC                   QUADSPI_SR_TCF  
#define QSPI_FLAG_TE                   QUADSPI_SR_TEF  
#define QSPI_IT_TO                          QUADSPI_CR_TOIE 
#define QSPI_IT_SM                          QUADSPI_CR_SMIE 
#define QSPI_IT_FT                          QUADSPI_CR_FTIE 
#define QSPI_IT_TC                          QUADSPI_CR_TCIE 
#define QSPI_IT_TE                          QUADSPI_CR_TEIE 
#define HAL_QPSI_TIMEOUT_DEFAULT_VALUE ((uint32_t)5000)/* 5 s */

/* Exported macros -----------------------------------------------------------*/
#define __HAL_QSPI_RESET_HANDLE_STATE(__HANDLE__)           ((__HANDLE__)->State = HAL_QSPI_STATE_RESET)

#define __HAL_QSPI_ENABLE(__HANDLE__)                       SET_BIT((__HANDLE__)->Instance->CR, QUADSPI_CR_EN)

#define __HAL_QSPI_DISABLE(__HANDLE__)                      CLEAR_BIT((__HANDLE__)->Instance->CR, QUADSPI_CR_EN)

#define __HAL_QSPI_ENABLE_IT(__HANDLE__, __INTERRUPT__)     SET_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__))


#define __HAL_QSPI_DISABLE_IT(__HANDLE__, __INTERRUPT__)    CLEAR_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__))

#define __HAL_QSPI_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (READ_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__)) == (__INTERRUPT__)) 

#define __HAL_QSPI_GET_FLAG(__HANDLE__, __FLAG__)           (READ_BIT((__HANDLE__)->Instance->SR, (__FLAG__)) != 0)

#define __HAL_QSPI_CLEAR_FLAG(__HANDLE__, __FLAG__)         WRITE_REG((__HANDLE__)->Instance->FCR, (__FLAG__))

/* Exported functions --------------------------------------------------------*/
/* Initialization/de-initialization functions  ********************************/
HAL_StatusTypeDef     HAL_QSPI_Init     (QSPI_HandleTypeDef *hqspi);
HAL_StatusTypeDef     HAL_QSPI_DeInit   (QSPI_HandleTypeDef *hqspi);
void                  HAL_QSPI_MspInit  (QSPI_HandleTypeDef *hqspi);
void                  HAL_QSPI_MspDeInit(QSPI_HandleTypeDef *hqspi);
/* IO operation functions *****************************************************/
/* QSPI IRQ handler method */
void                  HAL_QSPI_IRQHandler(QSPI_HandleTypeDef *hqspi);

/* QSPI indirect mode */
HAL_StatusTypeDef     HAL_QSPI_Command      (QSPI_HandleTypeDef *hqspi, QSPI_CommandTypeDef *cmd, uint32_t Timeout);
HAL_StatusTypeDef     HAL_QSPI_Transmit     (QSPI_HandleTypeDef *hqspi, uint8_t *pData, uint32_t Timeout);
HAL_StatusTypeDef     HAL_QSPI_Receive      (QSPI_HandleTypeDef *hqspi, uint8_t *pData, uint32_t Timeout);
HAL_StatusTypeDef     HAL_QSPI_Command_IT   (QSPI_HandleTypeDef *hqspi, QSPI_CommandTypeDef *cmd);
HAL_StatusTypeDef     HAL_QSPI_Transmit_IT  (QSPI_HandleTypeDef *hqspi, uint8_t *pData);
HAL_StatusTypeDef     HAL_QSPI_Receive_IT   (QSPI_HandleTypeDef *hqspi, uint8_t *pData);
HAL_StatusTypeDef     HAL_QSPI_Transmit_DMA (QSPI_HandleTypeDef *hqspi, uint8_t *pData);
HAL_StatusTypeDef     HAL_QSPI_Receive_DMA  (QSPI_HandleTypeDef *hqspi, uint8_t *pData);

/* QSPI status flag polling mode */
HAL_StatusTypeDef     HAL_QSPI_AutoPolling   (QSPI_HandleTypeDef *hqspi, QSPI_CommandTypeDef *cmd, QSPI_AutoPollingTypeDef *cfg, uint32_t Timeout);
HAL_StatusTypeDef     HAL_QSPI_AutoPolling_IT(QSPI_HandleTypeDef *hqspi, QSPI_CommandTypeDef *cmd, QSPI_AutoPollingTypeDef *cfg);

/* QSPI memory-mapped mode */
HAL_StatusTypeDef     HAL_QSPI_MemoryMapped(QSPI_HandleTypeDef *hqspi, QSPI_CommandTypeDef *cmd, QSPI_MemoryMappedTypeDef *cfg);
/* Callback functions in non-blocking modes ***********************************/
void                  HAL_QSPI_ErrorCallback        (QSPI_HandleTypeDef *hqspi);
void                  HAL_QSPI_AbortCpltCallback    (QSPI_HandleTypeDef *hqspi);
void                  HAL_QSPI_FifoThresholdCallback(QSPI_HandleTypeDef *hqspi);

/* QSPI indirect mode */
void                  HAL_QSPI_CmdCpltCallback      (QSPI_HandleTypeDef *hqspi);
void                  HAL_QSPI_RxCpltCallback       (QSPI_HandleTypeDef *hqspi);
void                  HAL_QSPI_TxCpltCallback       (QSPI_HandleTypeDef *hqspi);
void                  HAL_QSPI_RxHalfCpltCallback   (QSPI_HandleTypeDef *hqspi);
void                  HAL_QSPI_TxHalfCpltCallback   (QSPI_HandleTypeDef *hqspi);

/* QSPI status flag polling mode */
void                  HAL_QSPI_StatusMatchCallback  (QSPI_HandleTypeDef *hqspi);

/* QSPI memory-mapped mode */
void                  HAL_QSPI_TimeOutCallback      (QSPI_HandleTypeDef *hqspi);
/* Peripheral Control and State functions  ************************************/
HAL_QSPI_StateTypeDef HAL_QSPI_GetState        (QSPI_HandleTypeDef *hqspi);
uint32_t              HAL_QSPI_GetError        (QSPI_HandleTypeDef *hqspi);
HAL_StatusTypeDef     HAL_QSPI_Abort           (QSPI_HandleTypeDef *hqspi);
HAL_StatusTypeDef     HAL_QSPI_Abort_IT        (QSPI_HandleTypeDef *hqspi);
void                  HAL_QSPI_SetTimeout      (QSPI_HandleTypeDef *hqspi, uint32_t Timeout);
HAL_StatusTypeDef     HAL_QSPI_SetFifoThreshold(QSPI_HandleTypeDef *hqspi, uint32_t Threshold);
uint32_t              HAL_QSPI_GetFifoThreshold(QSPI_HandleTypeDef *hqspi);
/* Private macros ------------------------------------------------------------*/
#define IS_QSPI_CLOCK_PRESCALER(PRESCALER)  ((PRESCALER) <= 0xFF)

#define IS_QSPI_FIFO_THRESHOLD(THR)         (((THR) > 0) && ((THR) <= 32))

#define IS_QSPI_SSHIFT(SSHIFT)              (((SSHIFT) == QSPI_SAMPLE_SHIFTING_NONE) || \
                                             ((SSHIFT) == QSPI_SAMPLE_SHIFTING_HALFCYCLE)) 

#define IS_QSPI_FLASH_SIZE(FSIZE)           (((FSIZE) <= 31))

#define IS_QSPI_CS_HIGH_TIME(CSHTIME)       (((CSHTIME) == QSPI_CS_HIGH_TIME_1_CYCLE) || \
                                             ((CSHTIME) == QSPI_CS_HIGH_TIME_2_CYCLE) || \
                                             ((CSHTIME) == QSPI_CS_HIGH_TIME_3_CYCLE) || \
                                             ((CSHTIME) == QSPI_CS_HIGH_TIME_4_CYCLE) || \
                                             ((CSHTIME) == QSPI_CS_HIGH_TIME_5_CYCLE) || \
                                             ((CSHTIME) == QSPI_CS_HIGH_TIME_6_CYCLE) || \
                                             ((CSHTIME) == QSPI_CS_HIGH_TIME_7_CYCLE) || \
                                             ((CSHTIME) == QSPI_CS_HIGH_TIME_8_CYCLE))   

#define IS_QSPI_CLOCK_MODE(CLKMODE)         (((CLKMODE) == QSPI_CLOCK_MODE_0) || \
                                             ((CLKMODE) == QSPI_CLOCK_MODE_3))

#define IS_QSPI_FLASH_ID(FLA)    (((FLA) == QSPI_FLASH_ID_1) || \
                                  ((FLA) == QSPI_FLASH_ID_2)) 
                                  
#define IS_QSPI_DUAL_FLASH_MODE(MODE)    (((MODE) == QSPI_DUALFLASH_ENABLE) || \
                                          ((MODE) == QSPI_DUALFLASH_DISABLE))
                                          
  
#define IS_QSPI_INSTRUCTION(INSTRUCTION)    ((INSTRUCTION) <= 0xFF) 

#define IS_QSPI_ADDRESS_SIZE(ADDR_SIZE)     (((ADDR_SIZE) == QSPI_ADDRESS_8_BITS)  || \
                                             ((ADDR_SIZE) == QSPI_ADDRESS_16_BITS) || \
                                             ((ADDR_SIZE) == QSPI_ADDRESS_24_BITS) || \
                                             ((ADDR_SIZE) == QSPI_ADDRESS_32_BITS))

#define IS_QSPI_ALTERNATE_BYTES_SIZE(SIZE)  (((SIZE) == QSPI_ALTERNATE_BYTES_8_BITS)  || \
                                             ((SIZE) == QSPI_ALTERNATE_BYTES_16_BITS) || \
                                             ((SIZE) == QSPI_ALTERNATE_BYTES_24_BITS) || \
                                             ((SIZE) == QSPI_ALTERNATE_BYTES_32_BITS))                                               


#define IS_QSPI_DUMMY_CYCLES(DCY)           ((DCY) <= 31) 

#define IS_QSPI_INSTRUCTION_MODE(MODE)      (((MODE) == QSPI_INSTRUCTION_NONE)    || \
                                             ((MODE) == QSPI_INSTRUCTION_1_LINE)  || \
                                             ((MODE) == QSPI_INSTRUCTION_2_LINES) || \
                                             ((MODE) == QSPI_INSTRUCTION_4_LINES))  

#define IS_QSPI_ADDRESS_MODE(MODE)          (((MODE) == QSPI_ADDRESS_NONE)    || \
                                             ((MODE) == QSPI_ADDRESS_1_LINE)  || \
                                             ((MODE) == QSPI_ADDRESS_2_LINES) || \
                                             ((MODE) == QSPI_ADDRESS_4_LINES))

#define IS_QSPI_ALTERNATE_BYTES_MODE(MODE)  (((MODE) == QSPI_ALTERNATE_BYTES_NONE)    || \
                                             ((MODE) == QSPI_ALTERNATE_BYTES_1_LINE)  || \
                                             ((MODE) == QSPI_ALTERNATE_BYTES_2_LINES) || \
                                             ((MODE) == QSPI_ALTERNATE_BYTES_4_LINES))

#define IS_QSPI_DATA_MODE(MODE)             (((MODE) == QSPI_DATA_NONE)    || \
                                             ((MODE) == QSPI_DATA_1_LINE)  || \
                                             ((MODE) == QSPI_DATA_2_LINES) || \
                                             ((MODE) == QSPI_DATA_4_LINES))

#define IS_QSPI_DDR_MODE(DDR_MODE)          (((DDR_MODE) == QSPI_DDR_MODE_DISABLE) || \
                                             ((DDR_MODE) == QSPI_DDR_MODE_ENABLE))

#define IS_QSPI_DDR_HHC(DDR_HHC)            (((DDR_HHC) == QSPI_DDR_HHC_ANALOG_DELAY) || \
                                             ((DDR_HHC) == QSPI_DDR_HHC_HALF_CLK_DELAY))

#define IS_QSPI_SIOO_MODE(SIOO_MODE)      (((SIOO_MODE) == QSPI_SIOO_INST_EVERY_CMD) || \
                                             ((SIOO_MODE) == QSPI_SIOO_INST_ONLY_FIRST_CMD))

#define IS_QSPI_INTERVAL(INTERVAL)        ((INTERVAL) <= QUADSPI_PIR_INTERVAL) 

#define IS_QSPI_STATUS_BYTES_SIZE(SIZE)   (((SIZE) >= 1) && ((SIZE) <= 4)) 

#define IS_QSPI_MATCH_MODE(MODE)            (((MODE) == QSPI_MATCH_MODE_AND) || \
                                             ((MODE) == QSPI_MATCH_MODE_OR)) 
                                             
#define IS_QSPI_AUTOMATIC_STOP(APMS)        (((APMS) == QSPI_AUTOMATIC_STOP_DISABLE) || \
                                             ((APMS) == QSPI_AUTOMATIC_STOP_ENABLE))                                                                                                                                                                                                                                    

#define IS_QSPI_TIMEOUT_ACTIVATION(TCEN)    (((TCEN) == QSPI_TIMEOUT_COUNTER_DISABLE) || \
                                             ((TCEN) == QSPI_TIMEOUT_COUNTER_ENABLE)) 

#define IS_QSPI_TIMEOUT_PERIOD(PERIOD)      ((PERIOD) <= 0xFFFF) 

#define IS_QSPI_GET_FLAG(FLAG)              (((FLAG) == QSPI_FLAG_BUSY) || \
                                             ((FLAG) == QSPI_FLAG_TO)   || \
                                             ((FLAG) == QSPI_FLAG_SM)   || \
                                             ((FLAG) == QSPI_FLAG_FT)   || \
                                             ((FLAG) == QSPI_FLAG_TC)   || \
                                             ((FLAG) == QSPI_FLAG_TE))    

#define IS_QSPI_IT(IT)                      ((((IT) & (uint32_t)0xFFE0FFFFU) == 0x00000000U) && ((IT) != 0x00000000U))

/* Private functions ---------------------------------------------------------*/
#ifdef __cplusplus
}
#endif

#endif /* __STM32F7xx_HAL_QSPI_H */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/